Home > Moisture
Testing
> Aggrameter® >


Aggrameter®
For instantaneous determination of the moisture content
of sand, fine aggregate and coarse aggregate
using a unique microwave sensor

Aggrameter® Hand Held Microwave Moisture Meter For Fine and Coarse Aggregates
Aggrameter® Complete System with case and Extension Pole


 
Alternative Views:


Questions?

Contact us for more information!


Get a Quote!!
For orders outside the United States and Canada please contact us and we will be happy to get you a complete quote.
If you are not sure on what item to buy, please see our Purchasing Notes below or contact usand we'll be glad to assist you on your order.

We also offer an "Add extended warranty" option to your purchased instrument! Just add it to your cart
.
The instruction manual for this equipment can be found here:
Aggrameter® Manual


James Instruments - Aggrameter (tm) introduction
Item# Item Name Price Qty Add
T-T-100 Aggrameter® Complete System
Includes Meter, Sensor Probe, Sensor Cable and Software
$2,617.00
T-T-100-ext Extended Warrunty for Aggrameter™
$797.00
Check the items you wish to purchase, then click


Product Description:
Untitled Document


Aggrameter®

For instantaneous determination of the moisture content of sand, fine aggregate and coarse aggregate using a unique microwave sensor


Purchasing Notes

  • The T-T-100 Aggrameter® is for use only with sand and aggregates, for soils please review the Aquaprobe


Features & Benefits

  • Fast and easy to use; simply insert the prongs into the sand or aggregate being tested

  • Accurate & Instantaneous

  • Extension Pole for Less Fatigue

  • Completely Portable

  • Customizable for Different Materials

  • Easy to Read Display


Product Information

A Microwave meter for rapid determination of moisture content in sand and other fine and coarse aggregates.

The Aggrameter® T-T-100 utilizes the latest microwave and microprocessor technology to measure moisture content in various fine and coarse-grained materials. The prongs of the probe are inserted into the material to be tested and the percentage of moisture content is instantaneously shown on the easy to read display.

An average of five to ten readings is normally taken in order to ensure a valid result. This output is converted by the integrated microprocessor and the moisture content is displayed directly as a percentage of dry weight. The Aggrameter® comes calibrated for both sand and aggregate, and can be programmed by the user with up to ten different materials. The maximum aggregate particle size to be tested is approximately 3/8" (or 9.5 mm) in diameter.

The Aggrameter® can store more than 150 readings - complete with time and date for future reference. Data can be recalled via USB interface to a personal computer.


Aggralinx®

The Aggralinx® software will allow connection of the instrument to a Windows 7, 8 or 10 personal computer. All the data stored by the unit can be uploaded to the personal computer for inclusion in quality control reports or any other form for later analysis. The software will also allow the user to ‘customize’ the Aggrameter® to a specific material. This will dramatically increase the accuracy of the unit.


Specifications

Moisture Range: 0 - 20% by Dry Weight
Frequency: 50 Mhz
Power: 2 AA Batteries
Display: 2 x 16 Char. Trans - reflective
Data Link: USB
Weight: 1.8 kg4 lbs. (4 lbs.)
Length Extended: 1000mm (36 Inches)
Data Storage: Greater Than 1000 Readings
Prongs Length: 77mm (three inches)


Downloadable Documents



Downloadable Software



Downloadable Instruction Manual






Instructions:

Calibration Procedures

  • Dry a sample of material in low heat using a bake oven. (It is suggested to weigh the sample prior to drying.)
  • When the sample has lost all of it's internal moisture, the calibration process of the material can be started. (Note: This may take several hours.) Weigh the dried sample.
  • Turn ON the Aggrameter®, T-T-100
  • Using the up or down arrows, scroll through the menu selection until Direct mode appears on the T-100 display. (It is recommended to erase all prior data saved on the T-T-100.) (See Instruction Manual pg.36, step 6.)
  • Take 10 readings for each percentage; starting at zero percent (or Oven Dry). Store each reading by pressing the Enter button.
  • Now slowly add water in 2 percent increments to the sample. (For a 4,000 gram sample, a 2 percent increment = 80 grams of water.)
  • Continue adding water to the sample in 2 percent increments, and taking & saving 10 readings for each increment.
  • After the T-T-100 has hit full saturation (the direct reading = 409.5 mV), uploading the saved data with the software is necessary.
  • Uploading can be done by connecting the Aggrameter® to a P.C. with the software using the supplied USB cable.
  • Use the provided instructions in the T-T-100 manual (page 34-35) to successfully accomplish calibration.
  • Once analyzation of the data has been completed using the T-T-100 software, the Offset and Gain values will be displayed.
    Record these values down for future use. Or... if these values are ever accidentally erased, they can then be reentered.
  • Return to the T-T-100 and enter a User Material program. (T-T-100 manual page 20 “Change user program”)
    Once the calculated Gain and Offset values have been entered into the T-T-100, calibration for that material is now completed.



Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Moisture
Testing
> Aggrameter®
Moisture
Testing

New Products